百度音乐盒M-100启动信息

8460

百度音乐盒M-100和小度路由一样也是用的MT7620A,也可以刷openwrt,不过还加了一个音频IC,当然我也用不到。
好的是,百度音乐盒里面的7620A是一个模块,只要把GPIO引脚弄清楚,就可以控制其他东西。
其启动信息如下:

 

## Booting image at bc050000 ...
raspi_read: from:50000 len:40
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 6680438 Bytes = 6.4 MB
Load Address: 80000000
Entry Point: 8000c310
raspi_read: from:50040 len:65ef76
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8000c310) ...
## Giving linux memsize in MB, 64

Starting kernel ...


LINUX started...

 THIS IS ASIC
Linux version 2.6.36 (root@192.168.2.100) (gcc version 3.4.2) #48 Fri Dec 20 23:29:43 EST 2013

 The CPU feqenuce set to 580 MHz

 MIPS CPU sleep mode enabled.
 PCIE: bypass PCIe DLL.
 PCIE: Elastic buffer control: Addr:0x68 -> 0xB4
 disable all power about PCIe
CPU revision is: 00019650 (MIPS 24Kc)
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 console=ttyS0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=0005c00b
Readback ErrCtl register=0005c00b
Memory: 59644k/65536k available (4171k kernel code, 5892k reserved, 774k data, 160k init, 0k highmem)
NR_IRQS:128
MTK/Ralink System Tick Counter init... cd:804bfe68, m:214748, s:32
console [ttyS1] enabled
Calibrating delay loop... 386.04 BogoMIPS (lpj=772096)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab  at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource Ralink external timer
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.29 [Flags: R/O].
fuse init (API version 7.15)
msgmni has been set to 116
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A
serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A
brd: module loaded
deice id : ef 40 17 0 0 (40170000)
W25Q64BV(ef 40170000) (8192 Kbytes)
mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536
Creating 7 MTD partitions on "raspi":
0x000000000000-0x000000800000 : "ALL"
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x0000001d5fb6 : "Kernel"
mtd: partition "Kernel" doesn't end on an erase block -- force read-only
0x0000001d5fb6-0x000001000000 : "RootFS"
mtd: partition "RootFS" extends beyond the end of device "raspi" -- size truncated to 0x62a04a
mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
0x000000050000-0x000001000000 : "Kernel_RootFS"
mtd: partition "Kernel_RootFS" extends beyond the end of device "raspi" -- size truncated to 0x7b0000
rdm_major = 253
SMACCR1 -- : 0x00009c41
SMACCR0 -- : 0x7cff5ca0
Ralink APSoC Ethernet Driver Initilization. v3.0  256 rx/tx descriptors allocated, mtu = 1500!
SMACCR1 -- : 0x00009c41
SMACCR0 -- : 0x7cff5ca0
PROC INIT OK!
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24


=== pAd = c0003000, size = 807232 ===

<-- RTMPAllocTxRxRingMemory, Status=0
<-- RTMPAllocAdapterBlock, Status=0
AP Driver version-2.7.1.6
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
nf_conntrack version 0.5.0 (931 buckets, 3724 max)
matchsize=264
IPVS: Registered protocols ()
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
802.1Q VLAN Support v1.8 Ben Greear 
All bugs added by David S. Miller 
VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
Freeing unused kernel memory: 160k freed
init started: BusyBox v1.12.1 (2013-07-10 03:23:19 EDT)
starting pid 32, tty '': '/etc_ro/rcS'
Algorithmics/MIPS FPU Emulator v1.5
Init GPIO by Hame
string2hex from 2218 to 2218
string2hex from 5 to 5
string2hex from 800 to 800
string2hex from 2000 to 2000
string2hex from 3f to 3f
string2hex from d00 to d00
string2hex from 0 to 0
string2hex from 0 to 0
string2hex from 0 to 0
string2hex from 0 to 0
Ralink gpio driver initialized 1a3318
devpts: called with bogus options
-------------------------------------------
Welcome to
        __  __     __     __    __  ______
        | | | |   /  \   |  \  /  | | ____|
        | |_| |  / /\ \  | |\\//| | | |___
        |  _  | |_/__\ \ | | \/ | | | |___|
        | | | | | |  | | | |    | | | |___
        |_| |_| |_|  |_| |_|    |_| |_____|
        HameData Technology Co., Ltd
-------------------------------------------
killall: goahead: no process killed
starting pid 49, tty '/dev/ttyS1': '/bin/sh'


BusyBox v1.12.1 (2013-07-10 03:23:19 EDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

# ******g_iplat = 1000*******
Start gpio 0 monitor
killall: udhcpc: no process killed
killall: udhcpc: no process killed
apcli0    no private ioctls.

ifconfig: ioctl 0x8913 failed: No such device
internet.sh
Password for 'admin' changed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller
rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1
rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000
rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller
rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2
rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
rmmod: ralink_wdt: No such file or directory
rmmod: cls: No such file or directory
rmmod: hw_nat: No such file or directory
rmmod: raeth: No such file or directory
insmod: bridge.ko: module not found
insmod: raeth.ko: module not found

##### disable 1st wireless interface #####
rmmod: rt2860v2_ap_net: No such file or directory
rmmod: rt2860v2_ap: No such file or directory
rmmod: rt2860v2_ap_util: No such file or directory
insmod: rt2860v2_ap_util.ko: module not found
insmod: rt2860v2_ap.ko: module not found
insmod: rt2860v2_ap_net.ko: module not found
RX DESC a3e6f000  size = 2048
RTMP_TimerListAdd: add timer obj c00988e0!
RTMP_TimerListAdd: add timer obj c0064000!
RTMP_TimerListAdd: add timer obj c0063fd4!
RTMP_TimerListAdd: add timer obj c0063fa8!
RTMP_TimerListAdd: add timer obj c000b070!
RTMP_TimerListAdd: add timer obj c000ac64!
RTMP_TimerListAdd: add timer obj c000b040!
RTMP_TimerListAdd: add timer obj c000b3e8!
RTMP_TimerListAdd: add timer obj c000b138!
RTMP_TimerListAdd: add timer obj c000b168!
RTMP_TimerListAdd: add timer obj c000b328!
RTMP_TimerListAdd: add timer obj c000b358!
RTMP_TimerListAdd: add timer obj c0066404!
RTMP_TimerListAdd: add timer obj c0065ff8!
RTMP_TimerListAdd: add timer obj c00663d4!
RTMP_TimerListAdd: add timer obj c006677c!
RTMP_TimerListAdd: add timer obj c00664cc!
RTMP_TimerListAdd: add timer obj c00664fc!
RTMP_TimerListAdd: add timer obj c0066434!
RTMP_TimerListAdd: add timer obj c0066464!
RTMP_TimerListAdd: add timer obj c0066494!
RTMP_TimerListAdd: add timer obj c006f24c!
RTMP_TimerListAdd: add timer obj c006f368!
RTMP_TimerListAdd: add timer obj c006f278!
RTMP_TimerListAdd: add timer obj c0066b24!
RTMP_TimerListAdd: add timer obj c0008530!
RTMP_TimerListAdd: add timer obj c0066838!
APSDCapable[0]=0
APSDCapable[1]=0
APSDCapable[2]=0
APSDCapable[3]=0
APSDCapable[4]=0
APSDCapable[5]=0
APSDCapable[6]=0
APSDCapable[7]=0
APSDCapable[8]=0
APSDCapable[9]=0
APSDCapable[10]=0
APSDCapable[11]=0
APSDCapable[12]=0
APSDCapable[13]=0
APSDCapable[14]=0
APSDCapable[15]=0
default ApCliAPSDCapable[0]=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
E2PROM: D0 target power=0xfa1e
 pAd->TemperatureRef25C = 0xfffffffa
E2PROM: 40 MW Power Delta= 0
3. Phy Mode = 9
RTMP_TimerListAdd: add timer obj c0008128!
AntCfgInit: primary/secondary ant 0/1
Initialize RF Central Registers for E2 !!!
Initialize RF Central Registers for E3 !!!
Initialize RF Channel Registers for E2 !!!
Initialize RF Channel Registers for E3 !!!
Initialize RF DCCal Registers for E2 !!!
Initialize RF DCCal Registers for E3 !!!
D1 = 0, D2 = 7, CalCode = 16 !!!
Current Temperature from BBP_R49=0xfffffff8
 TX BW Filter Calibration !!!
 RX BW Filter Calibration !!!
LOFT Calibration Done!
IQCalibration Start!
IQCalibration Done! CH = 0, (gain= 1, phase=3d)
IQCalibration Start!
IQCalibration Done! CH = 1, (gain= f, phase= 2)
TX IQ Calibration Done!
MCS Set = ff ff 00 00 00
Main bssid = 9c:41:7c:ff:5c:a8
<==== rt28xx_init, Status=0
0x1300 = 00064380
ifconfig: ioctl 0x8913 failed: No such device
brctl: bridge br0: No such device or address
iptables v1.4.10: can't initialize iptables table `mangle': Table does not exist (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
Raeth v3.0 (Tasklet,SkbRecycle)

phy_tx_ring = 0x035e2000, tx_ring = 0xa35e2000

phy_rx_ring0 = 0x035e3000, rx_ring0 = 0xa35e3000
SMACCR1 -- : 0x00009c41
SMACCR0 -- : 0x7cff5ca0
CDMA_CSG_CFG = 81000000
GDMA1_FWD_CFG = 20710000
vconfig: ioctl error for rem: No such device
vconfig: ioctl error for rem: No such device
rmmod: 8021q: No such file or directory
insmod: 8021q.ko: module not found
device eth2 entered promiscuous mode
##### config Ralink ESW vlan partition (LLLLW) #####
switch reg write offset=2004, value=ff0003
switch reg write offset=2104, value=ff0003
switch reg write offset=2204, value=ff0003
switch reg write offset=2304, value=ff0003
switch reg write offset=2404, value=ff0003
switch reg write offset=2504, value=ff0003
switch reg write offset=2010, value=810000c0
switch reg write offset=2110, value=810000c0
switch reg write offset=2210, value=810000c0
switch reg write offset=2310, value=810000c0
switch reg write offset=2410, value=810000c0
switch reg write offset=2510, value=810000c0
switch reg write offset=2610, value=81000000
switch reg write offset=2710, value=81000000
switch reg write offset=2604, value=20ff0003
switch reg write offset=2704, value=20ff0003
Special Tag Disabled
switch reg write offset=2610, value=81000000
switch reg write offset=2014, value=10001
switch reg write offset=2114, value=10001
switch reg write offset=2214, value=10001
switch reg write offset=2314, value=10001
switch reg write offset=2414, value=10002
switch reg write offset=2514, value=10001
REG_ESW_WT_MAC_ATC is 0x7ff0002
done.
device ra0 entered promiscuous mode
device eth2.1 entered promiscuous mode
wan.sh: unknown wan connection type: WIFI
br0: port 2(eth2.1) entering learning state
br0: port 2(eth2.1) entering learning state
br0: port 1(ra0) entering learning state
br0: port 1(ra0) entering learning state
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
br0: port 2(eth2.1) entering forwarding state
br0: port 1(ra0) entering forwarding state
killall: udhcpd: no process killed
Set: phy[1].reg[0] = 3900
Set: phy[2].reg[0] = 3900
Set: phy[3].reg[0] = 3900
Port0 is up. Skip.
ifconfig: ioctl 0x8913 failed: No such device
ADDRCONF(NETDEV_UP): apcli0: link is not ready
killall rt2860apd 1>/dev/null 2>&1
iptables -F -t filter 1>/dev/null 2>&1
iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -F macipport_filter 1>/dev/null 2>&1
iptables -D FORWARD -j web_filter  1>/dev/null 2>&1
iptables -F web_filter  1>/dev/null 2>&1
iptables -D FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -F malicious_filter  1>/dev/null 2>&1
iptables -D INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -F malicious_input_filter  1>/dev/null 2>&1
iptables -P INPUT ACCEPT
iptables -P OUTPUT ACCEPT
iptables -P FORWARD ACCEPT
iptables -t filter -N web_filter 1>/dev/null 2>&1
iptables -t filter -N macipport_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_input_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_filter -p tcp --syn -j synflood_filter 1>/dev/null 2>&1
iptables -t filter -A INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_input_filter -p tcp --syn -j synflood_input_filter 1>/dev/null 2>&1
iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1
/bin/super_dmz -f
sh: /bin/super_dmz: not found
iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1
iptables -t nat -F port_forward  1>/dev/null 2>&1; iptables -t nat -X port_forward  1>/dev/null 2>&1
iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1
iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ  1>/dev/null 2>&1
iptables -t nat -F POSTROUTING 1>/dev/null 2>&1
iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1
iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j DMZ 1>/dev/null 2>&1
iptables -t nat -A POSTROUTING -o apcli0 -s 192.168.169.1/255.255.255.0 -j MASQUERADE 1>/dev/null 2>&1
ntp.sh
ddns.sh
pool.ntp.org: Unknown host
kill -9 `cat /var/run/wscd.pid.ra0`
cat: can't open '/var/run/wscd.pid.ra0': No such file or directory
kill: you need to specify whom to kill
iwpriv ra0 set WscConfMode=0 1>/dev/null 2>&1
route delete 239.255.255.250 1>/dev/null 2>&1
killall -q klogd
killall -q syslogd
syslogd -C8 1>/dev/null 2>&1
klogd 1>/dev/null 2>&1
killall -q zebra
killall -q ripd
Got same SSID
Got same SSID
Got same SSID
Got same SSID
Got same SSID
Got same SSID
7 RoBox 15182295670 ASCII WPA2PSK AES 3
Current Channel is 7 and Remote is 7 and extch is 3
udhcpc (v1.12.1) started
webs: Listening for HTTP requests at address 192.168.169.1
Enable Ralink GDMA Controller Module
GDMA IP Version=3
i2cdrv_major = 218
i2s_reset_tx_config
i2s_tx_config
i2s_clock_enable
Init Audio Decoder
i2s_tx_enable
********set vset vuxmode value = ffff0002
ol*********set unmute****************
ume 8********
auxmode = ffff0002
Start gpio 13 monitor
Start gpio 27 monitor
Start gpio 25 monitor
Start gpio 26 monitor
[00:00:26]3g.pid value is 5022
[00:00:26]Start Monitor Version:v1.0
receive msg
[00:00:26]Get a device change notify
[00:00:26]get signal from driver [0][0]36
start udisk
Start gpio 29 monitor
Start gpio 28 monitor
Start gpio 24 monitor
RTMP_TimerListAdd: add timer obj c00ae688!
RTMP_TimerListAdd: add timer obj c00ae840!
drivers/net/wireless/rt2860v2_ap/../rt2860v2/ap/ap_data.c:4354 assert pEntry->Aid == pRxWI->WirelessCliIDfailed
RTMP_TimerListAdd: add timer obj c00c22cc!
ioctl: Invalid argument
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udisk over
[00:00:29]Create socket 5
start listen socket[5]
LogLevel: 1
AirName: Baidu_music_f5ca
HWID: XP%&p
HWID_Hex(12): 005850252670
Listening on IPv4 Socket
daemon_reset_sigs
daemon_unblock_sigs
make_runtime_dir
daemon_pid_file_create
enforce_rlimits
chdir
avahi-daemon 0.6.31 starting up.
run_server
WARNING: No NSS support for mDNS detected, consider installing nss-mdns!
Failed to open /etc/resolv.conf: No such file or directory
No service file found in /etc/avahi/services.
Joining mDNS multicast group on interface br0.IPv4 with address 192.168.169.1.
New relevant interface br0.IPv4 for mDNS.
Network interface enumeration completed.
Registering new address record for fe80::9e41:7cff:feff:5ca0 on br0.*.
Registering new address record for 192.168.169.1 on br0.IPv4.
Registering new address record for fe80::9e41:7cff:feff:5ca7 on eth2.2.*.
Registering new address record for fe80::9e41:7cff:feff:5ca0 on eth2.1.*.
Registering new address record for fe80::9e41:7cff:feff:5ca9 on apcli0.*.
Registering new address record for fe80::9e41:7cff:feff:5ca8 on ra0.*.
Registering new address record for fe80::9e41:7cff:feff:5ca0 on eth2.*.
Registering HINFO record with values 'MIPS'/'LINUX'.
Bind socket to INADDR_ANY
wait client request...[5]...
Sending select for 192.168.1.13...
Lease of 192.168.1.13 obtained, lease time 86400
Joining mDNS multicast group on RTMP_TimerListAdd: add timer obj c00c2308!
interface apcli0.IPv4 with address 192.168.1.13.
New relevant interface apcli0.IPv4 for mDNS.
Registering new address record for 192.168.1.13 on apcli0.IPv4.
deleting routers
route: ioctl 0x890c failed: No such process
adding dns 192.168.1.1
rev success
killall -q ripd
Online set thread [5109]
check for androidplayer  -> 192.168.1.13
/sbin/config-igmpproxy.sh
/sbin/config-igmpproxy.sh: line 10: igmpproxy.sh: noRcv Wcid(1) AddBAReq
Start Seq = 00000002
RTMP_TimerListAdd: add timer obj c00c40dc!
t found
/sbin/config-igmpproxy.sh: line 10: igmpproxy.sh: not found
/sbin/config-igmpproxy.sh: line 12: igmpproxy: not found
/sbin/config-igmpproxy.sh: line 12: igmpproxy: not found
iptables -F -t filter 1>/dev/null 2>&1
iptables -D FORWARD -j macipport_filter 1>/dev/null 2>&1
Rcv Wcid(1) AddBAReq
Start Seq = 00000000
RTMP_TimerListAdd: add timer obj c00c412c!
25567 00030.771  191240.0    309.6  1393920333144711.3   4470.8         0
iptables -F macipport_filter 1>/dev/null 2>&1
iptables -D FORWARD -j web_filter  1>/dev/null 2>&1
iptables -F web_filter  1>/dev/null 2>&1
iptables -D FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -F malicious_filter  1>/dev/null 2>&1
Server startup complete. Host name is none.local. Local service cookie is 762465166.
iptables -D INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -F malicious_input_filter  1>/dev/null 2>&1
iptables -P INPUT ACCEPT
iptables -P OUTPUT ACCEPT
iptables -P FORWARD ACCEPT
iptables -t filter -N web_filter 1>/dev/null 2>&1
Bind socket to INADDR_ANY
wait client request...[6]...
iptables -t filter -N macipport_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_filter 1>/dev/null 2>&1
iptables -t filter -N malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -N synflood_input_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j web_filter 1>/dev/null 2>&1
Established under name '005850252670@Baidu_music_f5ca'
iptables -t filter -A FORWARD -j macipport_filter 1>/dev/null 2>&1
iptables -t filter -A FORWARD -j malicious_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_filter -p tcp --syn -j synflood_filter 1>/dev/null 2>&1
iptables -t filter -A INPUT -j malicious_input_filter 1>/dev/null 2>&1
iptables -t filter -A malicious_input_filter -p tcp --syn -j synflood_input_filter 1>/dev/null 2>&1
iptables -A FORWARD -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu 1>/dev/null 2>&1
/bin/super_dmz -f
sh: /bin/super_dmz: not found
iptables -t nat -D PREROUTING -j port_forward 1>/dev/null 2>&1
iptables -t nat -F port_forward  1>/dev/null 2>&1; iptables -t nat -X port_forward  1>/dev/null 2>&1
iptables -t nat -D PREROUTING -j DMZ 1>/dev/null 2>&1
iptables -t nat -F DMZ 1>/dev/null 2>&1; iptables -t nat -X DMZ  1>/dev/null 2>&1
iptables -t nat -F POSTROUTING 1>/dev/null 2>&1
iptables -t nat -N port_forward 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 1 -j port_forward 1>/dev/null 2>&1
iptables -t nat -N DMZ 1>/dev/null 2>&1; iptables -t nat -I PREROUTING 2 -j DMZ 1>/dev/null 2>&1
iptables -t nat -A POSTROUTING -o apcli0 -s 192.168.169.1/255.255.255.0 -j MASQUERADE 1>/dev/null 2>&1
killall: lcdaemon: no process killed
sh: lcdaemon: not found
41700 23204.329 113480.0 29.4 57457.6 6607.1 0

2 意见

回复 JiapengLi

Please enter your comment!
Please enter your name here