小度路由用的是ralink sdk开发的,其启动信息如下:
没明白的是RT2860v2为嘛都是都没找到，另外需要说明的是RT6352就是MT7620
U-Boot 1.1.3 (Nov 1 2013 - 13:49:26) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb4000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. spi_wait_nsec: 29 spi device id: c2 20 17 c2 20 (2017c220) find flash: MX25L6405D raspi_read: from:20000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.1.2.0 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Nov 1 2013 Time:13:49:26 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. You choosed 3 0 3: System Boot system code via Flash. ## Booting image at bc040000 ... raspi_read: from:40000 len:40 Image Name: Ai-BR Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 5018643 Bytes = 4.8 MB Load Address: 80000000 Entry Point: 8000c310 raspi_read: from:40040 len:4c9413 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c310) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.36 (chris@ubuntu-dt) (gcc version 3.4.2) #66 Thu Nov 21 18:35:00 CST 2013 The CPU feqenuce set to 580 MHz MIPS CPU sleep mode enabled. PCIE: bypass PCIe DLL. PCIE: Elastic buffer control: Addr:0x68 -> 0xB4 disable all power about PCIe CPU revision is: 00019650 (MIPS 24Kc) Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00004000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0 PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Writing ErrCtl register=0005e733 Readback ErrCtl register=0005e733 Memory: 56188k/65536k available (4353k kernel code, 9348k reserved, 800k data, 3400k init, 0k highmem) NR_IRQS:128 MTK/Ralink System Tick Counter init... cd:804efe78, m:214748, s:32 console [ttyS1] enabled Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource Ralink external timer NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RT3xxx EHCI/OHCI init. JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc. fuse init (API version 7.15) msgmni has been set to 109 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) Ralink gpio driver initialized RALINK_REG_PIODATA=00fc7f87 Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A brd: module loaded deice id : c2 20 17 c2 20 (2017c220) MX25L6405D(c2 2017c220) (8192 Kbytes) mtd .name = raspi, .size = 0x00800000 (0M) .erasesize = 0x00000008 (0K) .numeraseregions = 65536 Creating 6 MTD partitions on "raspi": 0x000000000000-0x000000800000 : "ALL" 0x000000000000-0x000000020000 : "Bootloader" 0x000000020000-0x000000030000 : "Config" 0x000000030000-0x000000040000 : "Factory" 0x000000040000-0x000000600000 : "Kernel" 0x000000600000-0x000000800000 : "Baidu" SMACCR1 -- : 0x0000240a SMACCR0 -- : 0x64fe4307 Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500! SMACCR1 -- : 0x0000240a SMACCR0 -- : 0x64fe4307 PROC INIT OK! PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 === pAd = c0198000, size = 625304 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 AP Driver version-2.7.1.6 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. nf_conntrack version 0.5.0 (877 buckets, 3508 max) matchsize=264 IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. GRE over IPv4 demultiplexor driver gre: can't add protocol ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> Freeing unused kernel memory: 3400k freed init started: BusyBox v1.12.1 (Algorithmics/MIPS FPU Emulator v1.5 2013-11-18 10:23:01 CST) starting devpts: called with bogus options pid 31, tty '': '/etc_ro/rcS' mount: mounting none on /proc/bus/usb failed: No such file or directory Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= boa: waiting for nvram_daemon starting pid 43, tty '/dev/ttyS1': '/bin/monitor' starting pid 42, tty '/dev/ttyS1': '/bin/sh' XXXXXXXXXXX1:5 BusyBox v1.12.1 (2013-11-18 10:23:01 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. # ----------support asp+++ server_name :192.168.8.1+++ boa: server version Boa/0.94.14rc21 boa: server built Nov 21 2013 at 16:13:51. boa: starting server pid=46, port 80 Password for 'admin' changed rmmod: ralink_wdt: No such file or directory rmmod: cls: No such file or directory rmmod: hw_nat: No such file or directory rmmod: raeth: No such file or directory insmod: bridge.ko: module not found insmod: mii.ko: module not found insmod: raeth.ko: module not found ##### disable 1st wireless interface ##### rmmod: rt2860v2_ap_net: No such file or directory rmmod: rt2860v2_ap: No such file or directory rmmod: rt2860v2_ap_util: No such file or directory insmod: rt2860v2_ap_util.ko: module not found insmod: rt2860v2_ap.ko: module not found insmod: rt2860v2_ap_net.ko: module not found insmod: nf_conntrack_proto_gre.ko: module not found insmod: nf_nat_proto_gre.ko: module not found insmod: nf_conntrack_pptp.ko: module not found insmod: nf_nat_pptp.ko: module nRX DESC a2a2c000 size = 2048 ot found RTMP_TimerListAdd: add timer obj c02016c8! RTMP_TimerListAdd: add timer obj c01a0070! RTMP_TimerListAdd: add timer obj c019fc64! RTMP_TimerListAdd: add timer obj c01a0040! RTMP_TimerListAdd: add timer obj c01a03e8! RTMP_TimerListAdd: add timer obj c01a0138! RTMP_TimerListAdd: add timer obj c01a0168! RTMP_TimerListAdd: add timer obj c01a0328! RTMP_TimerListAdd: add timer obj c01a0358! RTMP_TimerListAdd: add timer obj c01d8034! RTMP_TimerListAdd: add timer obj c01d8150! RTMP_TimerListAdd: add timer obj c01d8060! RTMP_TimerListAdd: add timer obj c01cf85c! RTMP_TimerListAdd: add timer obj c019d530! RTMP_TimerListAdd: add timer obj c01cf570! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff20 E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 RTMP_TimerListAdd: add timer obj c019d12c! AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = 2, D2 = 11, CalCode = 21 !!! RT6352_Temperature_Init : BBPR49 = 0x2 RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff8 Current Temperature from BBP_R49=0xfffffff2 TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= 0, phase=3d) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 0, phase=3c) TX IQ Calibration Done! RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 01 SYNC - BBP R4 to 20MHz.l RTMP_TimerListAdd: add timer obj c01cfb48! Main bssid = 24:0a:64:fe:43:07 <==== rt28xx_init, Status=0 0x1300 = 00064380 ifconfig: ioctl 0x8913 failed: No such device brctl: bridge br0: No such device or address Raeth v3.0 (Tasklet,SkbRecycle) phy_tx_ring = 0x00cc0000, tx_ring = 0xa0cc0000 phy_rx_ring0 = 0x00cc1000, rx_ring0 = 0xa0cc1000 SMACCR1 -- : 0x0000240a SMACCR0 -- : 0x64fe4307 CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 vconfig: ioctl error for rem: No such device vconfig: ioctl error for rem: No such device rmmod: 8021q: No such file or directory insmod: 8021q.ko: module not found ##### config Ralink ESW vlan partition (LLLLW) ##### switch reg write offset=2004, value=ff0003 switch reg write offset=2104, value=ff0003 switch reg write offset=2204, value=ff0003 switch reg write offset=2304, value=ff0003 switch reg write offset=2404, value=ff0003 switch reg write offset=2504, value=ff0003 switch reg write offset=2010, value=810000c0 switch reg write offset=2110, value=810000c0 switch reg write offset=2210, value=810000c0 switch reg write offset=2310, value=810000c0 switch reg write offset=2410, value=810000c0 switch reg write offset=2510, value=810000c0 switch reg write offset=2610, value=81000000 switch reg write offset=2710, value=81000000 switch reg write offset=2604, value=20ff0003 switch reg write offset=2704, value=20ff0003 Special Tag Disabled switch reg write offset=2610, value=81000000 switch reg write offset=2014, value=10001 switch reg write offset=2114, value=10001 switch reg write offset=2214, value=10001 switch reg write offset=2314, value=10001 switch reg write offset=2414, value=10002 switch reg write offset=2514, value=10001 REG_ESW_WT_MAC_ATC is 0x7ff0002 done. device ra0 entered promiscuous mode device eth2.1 entered promiscuous mode device eth2 entered promiscuous mode killall: udhcpc: no process killed killall: pppd: no process killed killall: l2tpd: no process killed killall: openl2tpd: no process killed udhcpc (v1.12.1) started killall: dnrd: no process killed br0: port 2(eth2.1) entering learning state br0: port 2(eth2.1) entering learning state br0: port 1(ra0) entering learning state br0: port 1(ra0) entering learning state ifconfig: ioctl 0x8914 failed: Cannot assign requested address ifconfig: ioctl 0x8914 failed: Cannot assign requested address br0: port 2(eth2.1) entering forwarding state br0: port 1(ra0) entering forwarding state killall: udhcpd: no process killed Set: phy[0].reg[0] = 3900 Set: phy[1].reg[0] = 3900 Set: phy[2].reg[0] = 3900 Set: phy[3].reg[0] = 3900 Set: phy[0].reg[0] = 3100 Set: phy[1].reg[0] = 3100 Set: phy[2].reg[0] = 3100 Set: phy[3].reg[0] = 3100 Unknown option: -I Unknown option: ra0 rm: cannot remove '/etc/radvd.conf': No such file or directory ADDRCONF(NETDEV_UP): sit0: link is not ready Set: phy[0].reg[0] = 3300 Set: phy[1].reg[0] = 3300 Set: phy[2].reg[0] = 3300 Set: phy[3].reg[0] = 3300 sh: /bin/super_dmz: not found killall: dnrd: no process killed dnrd --cache=off -L 192.168.8.1 -s 168.95.1.1 -s 8.8.8.8 & lanIp:192.168.8.1 Notice: caching turned off Notice: local DNS master turned off killall: updateFw: no process killed killall: inadyn: no process killed killall: phddns: no process killed Jan 1 00:00:24 miniupnpd[2126]: received signal 15, good-bye Unknown option: -I Unknown option: ra0 Jan 1 00:00:25 miniupnpd[7163]: WPS listening on port 7777 Jan 1 00:00:25 miniupnpd[7163]: HTTP listening on port 6352 ******************1 XXXXXXXXXXX2:45 cat: can't open '/var/run/baidu_daemon.pid': No such file or directory kill: you need to specify whom to kill /extraApps/baidu_daemon.bin& killall: ushare: no process killed [E- 1 0: 0:46] ------------------------------------------------- [E- 1 0: 0:46] baidu daemon is running [E- 1 0: 0:46] ------------------------------------------------- [W- 1 0: 0:46] Blink version: 0.9.8, arch: UCLINUX [I- 1 0: 0:46] got BAIDU_DB_DEVICEID: 898f9738-d930-4db4-a3cf-240a64fe4307 [I- 1 0: 0:46] got BAIDU_DB_DEVICENAME: aigale_Ai-BR100 [I- 1 0: 0:46] got BAIDU_DB_DLNA_NAME: Baidu AV-Router [W- 1 0: 0:46] got BAIDU_DB_FW_VERSION: v1.0.0.15 [W- 1 0: 0:46] Baidu Daemon process ID is 7195 [W- 1 0: 0:46] Local thread working... [W- 1 0: 0:46] TCP thread working... [I- 1 0: 0:46] init RTMPWorker success! ERROR: Problem accessing the DNS. (addr: msg.link.n.shifen.com) ERROR: RTMP_Connect failed! [E- 1 0: 0:46] RTMPWorker_start failed!, ret = -1 [W- 1 0: 0:46] start RTMPWorker error! [I- 1 0: 0:46] 1970 1 1 Thu 0: 0:46 [E- 1 0: 0:46] push_sdk_start_work_thread fail! rv = -30002 [F- 1 0: 0:46] init push thread failed with error code[-2] ushare.sh Baidu AV-Router br0 /media/ 3 ushare -D sleep 1 sleep 2 [I- 1 0: 0:48] Got OP_CONTROL_DLNACACHE_UPDATE event baidu time:1970:1:1 0:0:0 0
